23HF14

Tell us about any of your Land Rover related projects here.
User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: 23HF14

Post by removeduser185 » Fri Jun 26, 2020 9:00 pm

Thank you Andy. I was wondering how to sort out the backrest of my rear seat which was in a shocking state. It was sticky and scratched. I had just cleaned up the frame as I want to fit it and remove the two Britpart seats which simply don#t look right. Andy recommended some vinyl dye. I got some dark grey and the result is as shown - bearing in mind this is on top of a charcoal/almost black vinyl I think the finish is fantastic - certainly good enough to use. The backs are sprayed with a grey primer (the best match I could find) and then given a coat of satin varnish. I think it'll be fine.

Of course, the seat won't go in until I put it all back together again - though it is fun stripped down, but, my goodness, aren't old-fashioned wing a pain? I put them on while the doors are off to make it legal, but they're coming off afterwards! You can't see anything out of them and they really are in the way if you want to do anything with the engine. Talking of which - I am still fiddling with the carburettor - but this one goes better than all the others put together (apart from Jon S's) Talking of whom - the big box in the tub is the toolbox :D The other photo is simply there because it might as well be - and it hows the club badge!
IMG_0555.JPG
IMG_0555.JPG (1.19 MiB) Viewed 2360 times
IMG_0554.JPG
IMG_0554.JPG (1.01 MiB) Viewed 2360 times
Top off 25 Jun 2020.jpg
Top off 25 Jun 2020.jpg (409.94 KiB) Viewed 2360 times
Top off 1 25 Jun 2020.jpg
Top off 1 25 Jun 2020.jpg (210.97 KiB) Viewed 2360 times

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: 23HF14

Post by AR4412 » Fri Jun 26, 2020 9:10 pm

Hiya Fred! :D ,

That seatback looks cracking mate. 8-)

Don't get too carried away taking bits off the motor though, or you'll be back at the pile of bits stage again.

I've been working on an old SIII CL this week, and had to take it out on a road test to check out the speedo operation amongst other things, and it too has 'suicide mirrors' fitted. It was bad enough backing it out of the workshop, but changing lanes was a game of take a chance pot luck as to whether you got beeped at or not. God, I forgot how much I hate them.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: 23HF14

Post by removeduser185 » Tue Jun 30, 2020 7:16 pm

Of course, now I have renovated the seat, I shall need to put the upper tub sides back on to support it! It's interesting comparing the originals with the Britpart ones. By and large the aftermarket set-up is fine, but, why was the seat cushion made nearly 2" narrower, I wonder and why use black paint when the originals were galved - at least they might have used silver. But, of course, they are most easily identified by the exposed hardboard backs. So, I shall put my Britpart ones up for sale - though I'll need to keep a cushion back at least until I can find an original replacement - I suppose I could get the cushion I have recovered somewhere. We need the Land Rover spares days again so I can have a poke around!
IMG_0558.JPG
IMG_0558.JPG (1.07 MiB) Viewed 2325 times
IMG_0557.JPG
IMG_0557.JPG (1.1 MiB) Viewed 2325 times
IMG_0556.JPG
IMG_0556.JPG (1003.47 KiB) Viewed 2325 times
I must say, I am amazed at the quality of the vinyl dye - remarkable.

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: 23HF14

Post by removeduser185 » Thu Jul 16, 2020 10:49 pm

A couple of rather good days... I decided that my carburettor, while it was working sufficiently for the car to move reliably and was OK at speed, behaved like a dog at tickover. So, I sent off to Cyprus to the guy on the mask and stripey jersey for a Zenith overhaul kit. It was supposed to be original and NOS, but, I have my doubts. Anyway, I whipped the carb off and replaced it temporarily with my Chinese copy. Before I fitted that I gave it a refurbishment from the stuff I had - I made sure the two halves were flat, that the floats were set properly and so on. It still didn't work properly and the mixture control screw has absolutely no effect whatsoever! I could remove it completely I am sure and there would be no change!

Yesterday, I was able to refurbish the genuine Zenith. As I said, it had been working pretty well and I was surprised when I opened it up to see how much wear there was - which proved what I had always thought, that Zenith carbs should run reasonably no matter what condition they are in. Anyway, the spindle was loose, but the new one fitted well enough, the mixture screw was bent and ridged, but was easily replaced and so on and so forth. I finished it, put it back together and then fitted it today.

I am very pleased. It is now running pretty much as it should. I think I need to do a bit more adjustment, but it runs well and ticks over fine. The only issue i a bit of light popping going down hill with foot off the throttle. That suggests (I think) that the mixture is a bit weak - which is fine as I have plenty of adjustment left.

All this meant that I had a couple of runs out today - perhaps a total of twenty happy miles still stripped down - no flies in mouth or eyes, just pleasant motoring. And aren't those wing mirrors useless? They aren't as tight as they should be and the wind soon readjusted them for me!

Very pleased. Need some petrol now!

User avatar
fv1620
Bake Off Judge
Posts: 2268
Joined: Thu Oct 06, 2011 2:16 pm
Location: GB-CMN (formerly UK91)
Contact:

Re: 23HF14

Post by fv1620 » Thu Jul 16, 2020 11:11 pm

Sounds good but just keep away from those scarecrows spotted in your neighbourhood, they look a dodgy couple if I'm not mistaken.
Clive Elliott

Collecting military technical publications, researching into military vehicle electrical systems, licensed radio amateur since 1964 using microwave bands for tropospheric scatter.

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: 23HF14

Post by removeduser185 » Thu Jul 16, 2020 11:17 pm

fv1620 wrote: ↑
Thu Jul 16, 2020 11:11 pm
Sounds good but just keep away from those scarecrows spotted in your neighbourhood, they look a dodgy couple if I'm not mistaken.
:lol:

Looking forward to meeting up - are you good for a socially distanced cuppa?

User avatar
fv1620
Bake Off Judge
Posts: 2268
Joined: Thu Oct 06, 2011 2:16 pm
Location: GB-CMN (formerly UK91)
Contact:

Re: 23HF14

Post by fv1620 » Thu Jul 16, 2020 11:51 pm

In principle a jolly good idea, but not sure if I'm still in age related isolation. Lots of toiling in the fields going on at present : (
Clive Elliott

Collecting military technical publications, researching into military vehicle electrical systems, licensed radio amateur since 1964 using microwave bands for tropospheric scatter.

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: 23HF14

Post by removeduser185 » Fri Jul 17, 2020 9:29 pm

To be honest, I no longer have a clue what the rules are. I read the newspapers, but just what applies in England and what here in Wales, I have no idea. I haven't been out much anyway - a trip to Aberglasney the other day which was a treat, otherwise I have barely got further than Llandovery. I must say, I am looking forward to going to Malvern and Newbury again in due course. I wonder whether I shall take the Lightweight?

Talking of which, a little adjusting today and it is really good - like a sewing machine. I had a great drive round in it and no popping!

Here's a question, though. Why would the flasher relay tick as if the indicators were flashing when the engine is running? It doesn't happen if the engine has stopped, even if the ignition is on. Could it be picking up a magnetic field from the coil or the king lead to the dizzie, as both of them are close. It doesn't affect the working of the indicstors at all, the only evidence of it is the regular-ish tick. I have swapped over the unit for my old one and get the same result. Ideas, anyone?

User avatar
fv1620
Bake Off Judge
Posts: 2268
Joined: Thu Oct 06, 2011 2:16 pm
Location: GB-CMN (formerly UK91)
Contact:

Re: 23HF14

Post by fv1620 » Fri Jul 17, 2020 9:50 pm

Fred are you absolutely 100% certain that the ticking is from the relay?

The sound of a spark leaking from the HT system to earth might give a similar regular ticking?

Was the tea room open at the gardens?
Clive Elliott

Collecting military technical publications, researching into military vehicle electrical systems, licensed radio amateur since 1964 using microwave bands for tropospheric scatter.

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: 23HF14

Post by removeduser185 » Fri Jul 17, 2020 10:11 pm

Yes, if you put your hand on the flasher unit you can feel it - just not quite as strongly as when the indicators are flashing, but quite clearly. No, the tea rooms weren't open, but the manager told us that they would be opening next week, I think it was. A limited menu, but it'll be nice to sample her food again!

Post Reply