Page 2 of 2
Re: DIY Tools. Who has the best to share!?
Posted: Thu Jun 11, 2020 9:52 pm
by landylees
My contribution is also a steering relay spring compressor - first "tool" I ever made with the spot welder and the angle iron I used was too thin so it bends alarmingly when you are compressing the spring!

- Land Rover Special Tool 2.JPG (1.36 MiB) Viewed 12909 times
Re: DIY Tools. Who has the best to share!?
Posted: Thu Jun 11, 2020 10:17 pm
by andrewjsimpson1977
Oh it’s that game is it
I made mine by hammering some metal sheet over an edge.. it doesn’t have to be the most permanent tool you ever made..

- 8A0D718E-6B71-492E-B119-7987DA70857C.jpeg (782.19 KiB) Viewed 12904 times

- 1E65B548-14EC-411F-A82F-A0DCBB1F930C.jpeg (856.53 KiB) Viewed 12904 times
Re: DIY Tools. Who has the best to share!?
Posted: Fri Jun 12, 2020 2:32 pm
by weetchus
"bends alarmingly" hahaha
landylees wrote: ↑Thu Jun 11, 2020 9:52 pm
My contribution is also a steering relay spring compressor - first "tool" I ever made with the spot welder and the angle iron I used was too thin so it bends alarmingly when you are compressing the spring!
Land Rover Special Tool 2.JPG
Re: DIY Tools. Who has the best to share!?
Posted: Fri Jun 12, 2020 2:41 pm
by weetchus
I tried this approach and failed miserably. Seem to remember the lip of the tool was scarily tiny and getting the shaft in was hard as even a tiny lip stopped it. I went with the compressor tool option, but did get the spring in the belly at full force once... once only!
andrewjsimpson1977 wrote: ↑Thu Jun 11, 2020 10:17 pm
Oh it’s that game is it
I made mine by hammering some metal sheet over an edge.. it doesn’t have to be the most permanent tool you ever made..
8A0D718E-6B71-492E-B119-7987DA70857C.jpeg
1E65B548-14EC-411F-A82F-A0DCBB1F930C.jpeg
Re: DIY Tools. Who has the best to share!?
Posted: Fri Jun 12, 2020 2:52 pm
by andrewjsimpson1977
weetchus wrote: ↑Fri Jun 12, 2020 2:41 pm
I tried this approach and failed miserably. Seem to remember the lip of the tool was scarily tiny and getting the shaft in was hard as even a tiny lip stopped it. I went with the compressor tool option, but did get the spring in the belly at full force once... once only!
andrewjsimpson1977 wrote: ↑Thu Jun 11, 2020 10:17 pm
Oh it’s that game is it
I made mine by hammering some metal sheet over an edge.. it doesn’t have to be the most permanent tool you ever made..
8A0D718E-6B71-492E-B119-7987DA70857C.jpeg
1E65B548-14EC-411F-A82F-A0DCBB1F930C.jpeg
I just remember making dammed sure neither my face or unmentionables were directly in the firing line at any time. The process was:
1) Clamp it up
2) Rush it over to the relay body muttering rude words under my breath repeatedly
3) Tap it in the hole, while becoming temporarily religious
4) Release each clamp with the same care one might employ whilst taking the pin out of a very old and rusty grenade
5) Shout “YES!” loudly when you realise it has broken with tradition and gone in first time.
I believe from other’s experiences, that I was very lucky on this one.
Re: DIY Tools. Who has the best to share!?
Posted: Fri Jun 12, 2020 7:40 pm
by landylees
andrewjsimpson1977 wrote: ↑Fri Jun 12, 2020 2:52 pm
weetchus wrote: ↑Fri Jun 12, 2020 2:41 pm
I tried this approach and failed miserably. Seem to remember the lip of the tool was scarily tiny and getting the shaft in was hard as even a tiny lip stopped it. I went with the compressor tool option, but did get the spring in the belly at full force once... once only!
andrewjsimpson1977 wrote: ↑Thu Jun 11, 2020 10:17 pm
Oh it’s that game is it
I made mine by hammering some metal sheet over an edge.. it doesn’t have to be the most permanent tool you ever made..
8A0D718E-6B71-492E-B119-7987DA70857C.jpeg
1E65B548-14EC-411F-A82F-A0DCBB1F930C.jpeg
I just remember making dammed sure neither my face or unmentionables were directly in the firing line at any time. The process was:
1) Clamp it up
2) Rush it over to the relay body muttering rude words under my breath repeatedly
3) Tap it in the hole, while becoming temporarily religious
4) Release each clamp with the same care one might employ whilst taking the pin out of a very old and rusty grenade
5) Shout “YES!” loudly when you realise it has broken with tradition and gone in first time.
I believe from other’s experiences, that I was very lucky on this one.
Andy, given how much work you have to do on your project, shouldn't you be outside working on it so you have something to post later ?
Re: DIY Tools. Who has the best to share!?
Posted: Fri Jun 12, 2020 7:54 pm
by andrewjsimpson1977
I painted some nut plates what more do you want, blood?
Re: DIY Tools. Who has the best to share!?
Posted: Thu Jun 25, 2020 12:44 am
by weetchus
Haha. This thread needs to keep going. Love the "temporarily religious" comment.