transfer case
transfer case
Hello everyone, I have a mechanical question: between 40 and 60 km/h, 3rd and 4th gears produce a rumbling noise and cause vibration. To diagnose the issue, I first removed the front driveshaft, but nothing changed. I then put that back and removed the rear one; the noise was gone—it was a real relief. I had a spare rear driveshaft in stock and installed it, but the noise returned—not exactly the same sound, but still there. I’ve ordered new U-joints (haven't received them yet). I’m wondering if it might be a transfer case bearing (or bearings). My question is: is it possible to remove just the transfer case without taking the transmission out of the vehicle? Thanks for your feedback.
Re: transfer case
It is possible, but it's a heavy old lump to manoeuvrer around from underneath with the vehicle sat on it's wheels. Not so bad to do if the floor and seat box are out of the vehicle and the transfer box supported from above for lifting and lowering.
Regards,
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
Re: transfer case
Thanks 

Re: transfer case
Hello everyone, I'm contacting you again because my rear gearbox output bearing is making a grinding noise between 45 and 60 km/h, and of course, the brake drum is full of oil. I've replaced the seal twice and it's still the same; I've also replaced the flange. My question is, has anyone here ever replaced this bearing without removing the transfer case on a Land Rover? Is it possible?
Re: transfer case
I won't say it's impossible, but, it wouldn't be fun. It isn't a fun job with the transfer box upside down on the bench in the garage/workshop, especially if it is an all helical gear type. As well as the rear output/speedo drive housing, the front output housing has to be removed from the main casing to do the job, as the rear bearing bearing outer race has to be removed by knocking the output shaft assembly backwards to force it from the casing. Then the bearing/inner race has to be removed, as in knocked free, from the output shaft. All in all not a small or fun job laying on your back on the floor.
Have a look for an online workshop manual, or try to find an old Haynes manual, so you can see what needs to be done, and what you would be taking on.
Regards,
Have a look for an online workshop manual, or try to find an old Haynes manual, so you can see what needs to be done, and what you would be taking on.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.