Monty the rather rusty 2A - 37FG31
Re: Monty the rather rusty 2A - 37FG31
I find that the delightfully titled Butyrub gets my vote as one of the best sealants around. I use it a lot on sunroofs and rear side windows on later vehicles. http://www.soudal.eu/soudalweb/productD ... 10&ID=1877. If you are fitting laminated glass, beware - I haven't used it with laminated glass and some of these sealants react with the laminate layer causing bloom
Behind the alloy packing strips, is standard windscreen seal. You can get it from most suppliers under p/n 78159
https://www.paddockspares.com/78159-win ... etres.html
Behind the alloy packing strips, is standard windscreen seal. You can get it from most suppliers under p/n 78159
https://www.paddockspares.com/78159-win ... etres.html
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
diffwhine wrote: ↑Sat May 23, 2020 6:17 pmI find that the delightfully titled Butyrub gets my vote as one of the best sealants around. I use it a lot on sunroofs and rear side windows on later vehicles. http://www.soudal.eu/soudalweb/productD ... 10&ID=1877. If you are fitting laminated glass, beware - I haven't used it with laminated glass and some of these sealants react with the laminate layer causing bloom
Behind the alloy packing strips, is standard windscreen seal. You can get it from most suppliers under p/n 78159
https://www.paddockspares.com/78159-win ... etres.html
Great info thanks for that - so I’m thinking that assuming the screen frame is place face down (outside surface down) the Butyrub (I’m going to have that word stuck in my head now) goes into the screen frame before the panes drop in on top of it? Is that where you use it?
Re: Monty the rather rusty 2A - 37FG31
Correct - a nice bead all round to rest the glass against, then the windscreen strip (usually comes in 2.5m rolls) and then your alloy retainers. Its the same process as for the tail door glass.
Butyrub... Living proof that you should check brand names in multiple languages before going to market...!
Butyrub... Living proof that you should check brand names in multiple languages before going to market...!
Re: Monty the rather rusty 2A - 37FG31
I replaced both windows recently and used flexistrip on both sides. The day after I fitted them the heavens opened for 3 days continues certainly a test to see if it worked and glad to say it did.
Billy
Billy
24FM27
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
Good info thanks Billy.
Well today was another full day of work-work so tinkering was kept to a minimum. I have however just finished my third hour of tidying the garages, which are now cleared, swept, tools sorted back into boxes etc ready for the next stage.
For the rest of the week I plan to:
1. Make some repairs to the remaining damaged body panels
2. Fit the missing stud and bolt to the water pump
3. Finish the last few bits of welding on the bulkhead
4. DrIll out the two snapped off vent panel studs
5. Stop being so childish and bolting everything I find to the truck in the hope it will look finished..
Andy
Well today was another full day of work-work so tinkering was kept to a minimum. I have however just finished my third hour of tidying the garages, which are now cleared, swept, tools sorted back into boxes etc ready for the next stage.
For the rest of the week I plan to:
1. Make some repairs to the remaining damaged body panels
2. Fit the missing stud and bolt to the water pump
3. Finish the last few bits of welding on the bulkhead
4. DrIll out the two snapped off vent panel studs
5. Stop being so childish and bolting everything I find to the truck in the hope it will look finished..
Andy
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
Well, of the ‘to-do’ list I managed to get a couple of bits done. One of the vent panel mounting studs was drilled out, well...what I mean is, it was removed along with the remnants of its tube. I’ve ordered some more 9mm ID tube which will be tapped out to size with the correct thread (as soon as I figure out what it is by running a tap through one of the good holes). I still have one more to drill out. I don’t know what these buggers are made from, but I’ve killed several HSS bits so far.
I closed up the hole left by the tube’s exit with the MIG, leaving enough that I can drill to size when the new tube arrives. I also ‘spot welded’ around the edge of the dash fascia again with one of those fancy spot weld shrouds on the MIG gun. It worked really well, although some dressing of the welds was needed with the help of my faithful assistant Mr A Grinder. I had rushed some of the spot welds when I borrowed Howard’s magic metal sticking machine, so a bit of tidy up was needed. I’ve probably over done it now, but better safe than sorry.
Finally, I did a bit of lip-forming on the dash panel recess edges, which I still need to finish, but it’s really tedious work so a bit at a time will do for now.
After clean up and zinc primer:
I don’t think it will be long now before it gets proper paint. When some more MIG wire arrives I need to finish the dash box repairs and fit one missing mounting tab for the leg vanity covers, weld on the bracket for the voltage regulator, and a couple of clips for the wiring loom...and the whole thing needs tiger sealing everywhere to keep water out..
..that’s it for today. More in the week weather and work permitting.
All the best,
Andy
I closed up the hole left by the tube’s exit with the MIG, leaving enough that I can drill to size when the new tube arrives. I also ‘spot welded’ around the edge of the dash fascia again with one of those fancy spot weld shrouds on the MIG gun. It worked really well, although some dressing of the welds was needed with the help of my faithful assistant Mr A Grinder. I had rushed some of the spot welds when I borrowed Howard’s magic metal sticking machine, so a bit of tidy up was needed. I’ve probably over done it now, but better safe than sorry.
Finally, I did a bit of lip-forming on the dash panel recess edges, which I still need to finish, but it’s really tedious work so a bit at a time will do for now.
After clean up and zinc primer:
I don’t think it will be long now before it gets proper paint. When some more MIG wire arrives I need to finish the dash box repairs and fit one missing mounting tab for the leg vanity covers, weld on the bracket for the voltage regulator, and a couple of clips for the wiring loom...and the whole thing needs tiger sealing everywhere to keep water out..
..that’s it for today. More in the week weather and work permitting.
All the best,
Andy
Re: Monty the rather rusty 2A - 37FG31
Something LR themselves have never achieved on any vehicle they have ever built........andrewjsimpson1977 wrote: ↑Sun May 31, 2020 4:00 pm...and the whole thing needs tiger sealing everywhere to keep water out..
Good to see you're getting more done mucka.
Is it the thread size for the three vent panel bolts in the top of the bulkhead you need? If so, they're a 5/16" UNF.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
It’s the ones on the front face of the bulkhead matey (four of). In the top corners.AR4412 wrote: ↑Sun May 31, 2020 5:50 pmSomething LR themselves have never achieved on any vehicle they have ever built........andrewjsimpson1977 wrote: ↑Sun May 31, 2020 4:00 pm...and the whole thing needs tiger sealing everywhere to keep water out..
Good to see you're getting more done mucka.![]()
Is it the thread size for the three vent panel bolts in the top of the bulkhead you need? If so, they're a 5/16" UNF.
Regards,
Re: Monty the rather rusty 2A - 37FG31
Oh. Right there Ted. Do you mean the ones for the bolts on the 'feet' of the vent panel to pass through, highlighted below?
The four tubes are plain, Just measured mine and they work out at around 9.25/9.3 mm in new money, so 9mm might be enough, but a blast through with a 9.5 mm drill bit should see you with enough leeway to get all the bolts through with some wriggle room for alignment.
Regards,
The four tubes are plain, Just measured mine and they work out at around 9.25/9.3 mm in new money, so 9mm might be enough, but a blast through with a 9.5 mm drill bit should see you with enough leeway to get all the bolts through with some wriggle room for alignment.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.