Monty the rather rusty 2A - 37FG31

Tell us about any of your Land Rover related projects here.
chipbury
Master Baker
Posts: 1411
Joined: Sun Oct 02, 2011 3:26 pm
Location: Bath

Re: Monty the rather rusty 2A - 37FG31

Post by chipbury » Sun Aug 18, 2019 7:39 pm

Don’t tell anyone but I enjoyed some battenburg on Thursday, lovely it was.
2A - 39 FG 70

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Aug 18, 2019 7:44 pm

chipbury wrote: ↑
Sun Aug 18, 2019 7:39 pm
Don’t tell anyone but I enjoyed some battenburg on Thursday, lovely it was.
I've always said you were a good egg Chris :D

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Thu Aug 22, 2019 7:31 pm

Right so this evening on Tales from the Axminster, we have a couple of offerings to the restoration deities:

The nice man at the ball joint supplier sent me two right hand threads, and then another right hand thread. Finally a left hand thread arrived today allowing me to finish the recently straightened drag link. It’s since been fitted to the truck.

C484DC6B-68BF-4DA7-9482-3015A28694D2.jpeg
C484DC6B-68BF-4DA7-9482-3015A28694D2.jpeg (1.89 MiB) Viewed 2623 times

I also did the longitudinal rod a week or so ago but forgot to photograph it. Well, you’ve seen one you’ve seen them all.


I finally remembered to stick some new UJs on the rear prop. I still don’t like that green - when I get around to painting the rest of the landy, I’ll give this a coat of DBG too.

E81E55D5-C37D-41D7-8450-80811FDD8EB4.jpeg
E81E55D5-C37D-41D7-8450-80811FDD8EB4.jpeg (1.46 MiB) Viewed 2623 times

Still no Dremel. Turns out the vendor is a charlatan, and despite three messages, and a formal complaint to EBay he’s staying silent. A better look through his ‘96.6%’ positive profile revealed a lot of recent complaints about non-received items and generally unprofessional responses. What a dick. Anyway it’s probably just as well it didn’t turn up, as I’ve gone and trapped a nerve in my shoulder again. It happens about once a year at most, and is fairly debilitating. Aside from all the ‘alright Napoleon’ hilarities from my workmates, I’ve been generally useless for the last couple of days. Building the prop shaft took me two hours!

The good news is the new steel for the dash panel has arrived, and I’m officially off work for a week from tomorrow. Sadly I have to go to Jersey so no playtime for Andy, but on a lighter note my favourite chinese restaurant in the whole world is there, so I guess I’ll just have to suck it up.

At least the steering rods are all done. I’ve finished the brake pedal and master cylinder too so as soon as I get the bulkhead spotted back together in theory I’ll have a landy that steers and stops. Nice.

All the best,

Andy

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Fri Sep 13, 2019 8:25 pm

Right..so... it’s been a few weeks of holidays, boys weekend, family illness, one kernackered shoulder and a lot of actual work related work, but finally this weekend I should have some time to start on the dashboard using my newly delivered dremel.

In the meantime a couple of items by way of an update to tales from the Axminster:

3373B473-C189-46BD-96D2-E63C12DB2DF6.jpeg
3373B473-C189-46BD-96D2-E63C12DB2DF6.jpeg (862.64 KiB) Viewed 2311 times
AD3266C1-0E0A-4F93-9E3F-DE6FF02EF962.jpeg
AD3266C1-0E0A-4F93-9E3F-DE6FF02EF962.jpeg (1.4 MiB) Viewed 2311 times

The sill panel got lost in the post temporarily (its a conspiracy!) but looks great now I have test fitted it to the truck. Photo of that tomorrow when the sun’s up. Can someone please confirm the size of the mounting bolts? I struggle with the IPC for the Rover 1 particularly with finding the pages where half the bodywork is supposed to be

The seat belt bracket I ordered because I was unhappy with the state of one of mine, and I’m sort of stuck in “it must be right” mode.

The replacement (correct width) steel from the dash is sat in the dining room waiting for me to draw it out and start chopping, so hopefully tomorrow we’ll see some progress on that front.

All the best,

Andy

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Monty the rather rusty 2A - 37FG31

Post by removeduser185 » Fri Sep 13, 2019 9:08 pm

According to the IPC there are twelve (6 each side) 1/4"x 5/8" UNF which go along the tops of the sills and connect it to the floor and the lip of the seatbox and then four 5/16" x 3/4" slot headed domed screws which go into nutserts to hold the rear of the sill to the "dogs' ears". But, I'm not sure that's quite right as the bolts in the footwell differ from those along the side of the seatbox as they are slot-head domed bolts, again using nutserts, whereas those beside the seat box are straightforward bolts. I'll have a proper look tomorrow and see what the set-up is.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sat Sep 14, 2019 2:34 pm

Fred wrote: ↑
Fri Sep 13, 2019 9:08 pm
According to the IPC there are twelve (6 each side) 1/4"x 5/8" UNF which go along the tops of the sills and connect it to the floor and the lip of the seatbox and then four 5/16" x 3/4" slot headed domed screws which go into nutserts to hold the rear of the sill to the "dogs' ears". But, I'm not sure that's quite right as the bolts in the footwell differ from those along the side of the seatbox as they are slot-head domed bolts, again using nutserts, whereas those beside the seat box are straightforward bolts. I'll have a proper look tomorrow and see what the set-up is.
Thanks Ian, appreciate you taking the time to look.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sat Sep 14, 2019 2:47 pm

Right so I finally made some progress on the dash fascia today. First the cut out with pressed lipped edges..

Having templated the dash on a combination of Neil and Fred’s measurements (in the IT systems world we call that distributed processing :geek: ) I used the dremel to cut out the section inside of the inner lines I had drawn to allow for the lip:

7D8C7ED3-8DDE-4E48-83AF-BA2A5E326593.jpeg
7D8C7ED3-8DDE-4E48-83AF-BA2A5E326593.jpeg (1.2 MiB) Viewed 2276 times

Next I clamped up the edges one at a time between the removable piece from my metal folder, and an old file with a really straight edge. A variety of hammers, sockets, dollies, a bunt old chisel and some miscellaneous lumps of metal were used to tap the edges over and into shape. I found that by not quite hammering all the way to the ends of each line, the steel wanted to start making rounded corners without too much fuss. It was then a matter of hammering a socket into the corners sideways (thanks for the tip Neil) and the ‘pressing’ was complete. Well ok it still needs deburring but that’s a job for tomorrow.

DD62A358-46C7-416A-A144-B6F2370258E0.jpeg
DD62A358-46C7-416A-A144-B6F2370258E0.jpeg (775.43 KiB) Viewed 2276 times

BFEA9F68-BBDA-4C2D-8F8B-3AD0C52924D1.jpeg
BFEA9F68-BBDA-4C2D-8F8B-3AD0C52924D1.jpeg (728.07 KiB) Viewed 2276 times

Rear view showing the lip - it needs a fettle in a couple of places but it’s basically there. One down, two to go!

52276074-5275-4A93-8E4D-BEF539886CB3.jpeg
52276074-5275-4A93-8E4D-BEF539886CB3.jpeg (892.71 KiB) Viewed 2276 times
Last edited by andrewjsimpson1977 on Sat Sep 14, 2019 3:14 pm, edited 4 times in total.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sat Sep 14, 2019 2:59 pm

Next a quick check that the lips align nicely with the dash box:

C760E4E8-234A-4936-84E4-0FE6261CE497.jpeg
C760E4E8-234A-4936-84E4-0FE6261CE497.jpeg (977.76 KiB) Viewed 2275 times

.. before turning my attention to the heater panel. Again, template first then dremelled the shape out of sheet steel:

3A69D8B0-5AB2-4D84-A606-D11CC965BDBB.jpeg
3A69D8B0-5AB2-4D84-A606-D11CC965BDBB.jpeg (1.16 MiB) Viewed 2275 times

Then I started forming the lip on the curved section, where it will meet the contoured piece that I still need to make (tomorrow).

98E8E79D-445F-47E2-A99B-8235DDD974EC.jpeg
98E8E79D-445F-47E2-A99B-8235DDD974EC.jpeg (1.04 MiB) Viewed 2275 times
FCC1E795-E696-4443-A7B0-10823F73BBFA.jpeg
FCC1E795-E696-4443-A7B0-10823F73BBFA.jpeg (1.13 MiB) Viewed 2275 times
Again more deburring and a last minute tickle with the hammer is probably needed before it’s ready for spot welding, but I’m generally happy with these parts so far. I do need to ‘joggle’ the top edge where the heater panel meets the dash but first I’ll need to find a deep enough joggler.
Last edited by andrewjsimpson1977 on Sat Sep 14, 2019 3:46 pm, edited 5 times in total.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sat Sep 14, 2019 3:08 pm

Before packing up for the day, I had a go at getting a better alignment on the body panels, now the driver’s side sill is in place. I rescued the drivers door from the shed of spiders, and was surprised to find the rotten old door top unbolted easily this time. I remember the passenger side bolts being so rusted in they had to be cut off. I still need to dig out the remnants.

7BDEB4B5-DBF0-4277-84EA-C797BFDA33A5.jpeg
7BDEB4B5-DBF0-4277-84EA-C797BFDA33A5.jpeg (775.18 KiB) Viewed 2273 times

It’s clear that the bulkhead needs pulling toward at the top, but in fairness it’s not welded together yet, and doesn’t have its bar bolted in either. I have however added a couple of washers to the bulkhead main mounting bolts, which made the sill panel on the drivers side fit much better.

E1697547-EB18-4362-AB00-139F8B33C7F6.jpeg
E1697547-EB18-4362-AB00-139F8B33C7F6.jpeg (947.18 KiB) Viewed 2273 times

Looking at the old passenger side sill, that one is goosed too so I’ll get one on order and we can start the merry dance with the delivery gremlins again.

2046080A-4BB4-4C5E-AAE1-B4510C902A57.jpeg
2046080A-4BB4-4C5E-AAE1-B4510C902A57.jpeg (870.71 KiB) Viewed 2273 times

It’s taking shape. The current plan of getting all the pieces together before calling in Tony with his spot welder should mean that it all suddenly becomes ready for paint in a couple of week’s time. There. I had to say it didn’t I. I’ll never learn.

All the best,

Andy

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Sep 15, 2019 4:43 pm

A couple of spare hours this afternoon saw the contoured section (mostly) fabricated for mounting the gearbox tunnel..

Draw it out:

DCBFCBF3-09ED-4F2B-9624-A07AC1C8885F.jpeg
DCBFCBF3-09ED-4F2B-9624-A07AC1C8885F.jpeg (1022.06 KiB) Viewed 2211 times

Cut it out:

88E1E93F-190C-4F95-9C39-85714ECA5BC8.jpeg
88E1E93F-190C-4F95-9C39-85714ECA5BC8.jpeg (1.33 MiB) Viewed 2211 times

Bend the seam which mounts it to the heat panel I made yesterday. Ah look, it wants to start bending into a profile :D

6F20BC50-81AE-4737-A8DC-77A4DA06A516.jpeg
6F20BC50-81AE-4737-A8DC-77A4DA06A516.jpeg (1.39 MiB) Viewed 2211 times

Cut some Vs where the mounting tabs for the floor need to bend 90 degrees:

99920E50-AE75-42BF-BC23-2F06DEA5CC4D.jpeg
99920E50-AE75-42BF-BC23-2F06DEA5CC4D.jpeg (1.55 MiB) Viewed 2211 times
Last edited by andrewjsimpson1977 on Sun Sep 15, 2019 4:53 pm, edited 1 time in total.

Post Reply