Monty the rather rusty 2A - 37FG31
- removeduser185
- Cake Guru
- Posts: 3531
- Joined: Thu Jun 18, 2015 10:37 pm
Re: Monty the rather rusty 2A - 37FG31
Nice tyres!
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
A bit light update-wise this evening, due to a later than usual return from work. I do it deems owe Neil an apology... it turns out that the dynamo bracket isn’t a duplicate
when I looked down through the engine bay the other day, I thought “oh, there’s the edge of the front dynamo bracket”, and so assumed this one was a spare. That’ll teach me not to get underneath and look properly.. there are two front brackets for the dynamo, which clamp to the lower forward hole in the dynamo casing. So, after a scrub, it and the timing marker which goes with it, were derusted and in primer.
Black top coat on timing pointer thing:
I just need to do the black top coat later on the dynamo bracket and they can be fitted tomorrow.
Here they are being held while drying by my trusty assistant, Mr Robot.
He’s been helping me with stuff like this since I was five. True story.
So Neil, sorry for the unwitting fib mate.. but on the other hand how the hell did you see that from a wing lean Clark Kent!?!?
In other news, the trip under the engine to look at the dynamo reminded me that the engine hadn’t been spun in a while. So it was off with the trumpet and on with the civvy dog, and with the help of massive wrench number 1, the engine spun nice and smoothly, accompanied by the reassuring sound of the pistons going up and down, which allayed any fears that the thing had seized over the winter. I confess to having been a bit worried about that. What a relief.
Sorry it’s a bit barrel-scrapey this time, I will do better tomorrow.
Night all!
Andy
Black top coat on timing pointer thing:
I just need to do the black top coat later on the dynamo bracket and they can be fitted tomorrow.
Here they are being held while drying by my trusty assistant, Mr Robot.
He’s been helping me with stuff like this since I was five. True story.
So Neil, sorry for the unwitting fib mate.. but on the other hand how the hell did you see that from a wing lean Clark Kent!?!?
In other news, the trip under the engine to look at the dynamo reminded me that the engine hadn’t been spun in a while. So it was off with the trumpet and on with the civvy dog, and with the help of massive wrench number 1, the engine spun nice and smoothly, accompanied by the reassuring sound of the pistons going up and down, which allayed any fears that the thing had seized over the winter. I confess to having been a bit worried about that. What a relief.
Sorry it’s a bit barrel-scrapey this time, I will do better tomorrow.
Night all!
Andy
- removeduser185
- Cake Guru
- Posts: 3531
- Joined: Thu Jun 18, 2015 10:37 pm
Re: Monty the rather rusty 2A - 37FG31
It's just great to be able to follow your thread again. Some good work there - makes me rather nostalgic - as I've said before, sometimes it's better to travel than to arrive. Having said that, I'd hardly call my Lightweight journey complete - the thing is still waiting for a tune-up. If I leave it much longer it'll have flat spots on the tyres!
Re: Monty the rather rusty 2A - 37FG31
Hiya Andy!andrewjsimpson1977 wrote: ↑Thu May 30, 2019 9:38 pmSo Neil, sorry for the unwitting fib mate.. but on the other hand how the hell did you see that from a wing lean Clark Kent!?!?
No amazing observational skills on my part mate. I recognized the bracket from it's shape as being the same as my FFR idler's one, and know that is the same one as used on the dynamo. Your's doesn't have an FFR idler, but does have a dynamo. Et Voila! (More Poirot than Kent.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
Re: Monty the rather rusty 2A - 37FG31
Hi, interesting to read you used glue. Are you using glue extensively on your panels as additional strength? What glue are you using? A weld glue?
Thanks
Alex
Thanks
Alex
andrewjsimpson1977 wrote: ↑Mon May 27, 2019 8:56 pm...which were cleaned up and primered, and left to dry while I had my dinner. If Sara asks I had a healthy salad, and definitely not a frozen pizza from the petrol station.
Lined up with a bit of wood and some metal shims until the right height was achieved:
B4204B15-8D46-445F-819A-0AA02D709A94.jpeg
After the first couple of holes were drilled it became apparent that access for at least one of the others would be limited round the backso I grabbed the stiffener
and bolted it through the first two holes to be used as a drilling template.
84C73BEB-0627-4BBD-8AEE-B13840266A76.jpeg
Next, a quick check using the base bracket for the door striker (Its actually driver’s side one but it was to hand and the hole pattern is identical)
F233C544-BF12-4EB8-8952-7D6BBDEF3C9F.jpeg
..and finally happy that the bracket was positioned correctly, it was glued and bolted up for a few days to cure:
0B4990B1-E012-4C8E-970B-EE34F7FF4963.jpeg
I also fitted some more rivets, fastening the tub floor front to the valance panel, and the underside of the seat back panel, also to the valance.
I nearly forgot - have also fitted the driver's side dog ear, but then you've seen one of those already. It's coming together nicely - really pleased to see something vaguely truck-shaped appearing from the murky depths of the garage.
That’s it for tonight - I dug out the seat box parts for cleaning up as that will be the next big piece of the jigsaw. It doesn’t look too bad, but I’ll save those photos for another day.
All the best,
Andy
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
Hi Alex,
It’s a high shear strength epoxy, but generally I’ve only used it in a couple of small places, and have so far backed up the glue with rivets where needed.
Well I promised a better update this evening, but in reality the big tidy out of the garages took three hours, and I still have to put all the tools into their respective boxes and take the rubbish to the local tip.
I did manage to faff around getting the previously forgotten front bracket on the dynamo, along with the timing pointer thingy:
My god it took a lot of d*cking around. One of the bolts is trapped behind the double pulley, so I had to get the dog back off and get the puller out to yank the pulley off. (That’s quite a sentence).
Then as per blooming usual the brackets would only align with the mounting holes if the bolts were fitted in a particular order (thanks Land Rover) AND then I realised one of the original bolts wasn’t long enough because the addition of the front bracket made the combined hole it had to pass through too long.
Gah! I managed to find an old longer bolt (no doubt actually the original, Sod’s law) and on it all went at the fifth attempt.
After refitting the pulley and dog, I turned the engine over until it lined up the slot with the left-most pointer spike (for higher octane petrol) and unclamped and turned the dizzy until the arm pointed at the contact for number 1 spark plug.
So that’s one job off the list
I need, and will now have, beer.
Andy out.
It’s a high shear strength epoxy, but generally I’ve only used it in a couple of small places, and have so far backed up the glue with rivets where needed.
Well I promised a better update this evening, but in reality the big tidy out of the garages took three hours, and I still have to put all the tools into their respective boxes and take the rubbish to the local tip.
I did manage to faff around getting the previously forgotten front bracket on the dynamo, along with the timing pointer thingy:
My god it took a lot of d*cking around. One of the bolts is trapped behind the double pulley, so I had to get the dog back off and get the puller out to yank the pulley off. (That’s quite a sentence).
Then as per blooming usual the brackets would only align with the mounting holes if the bolts were fitted in a particular order (thanks Land Rover) AND then I realised one of the original bolts wasn’t long enough because the addition of the front bracket made the combined hole it had to pass through too long.
Gah! I managed to find an old longer bolt (no doubt actually the original, Sod’s law) and on it all went at the fifth attempt.
After refitting the pulley and dog, I turned the engine over until it lined up the slot with the left-most pointer spike (for higher octane petrol) and unclamped and turned the dizzy until the arm pointed at the contact for number 1 spark plug.
So that’s one job off the list
I need, and will now have, beer.
Andy out.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
A bit of a late update today, with a few small pieces progressing..
The old U-channel removed from the passenger side was used to make a template for the rivet holes into the light cluster. I had some luck here and the drill passed through into the original holes in the panel behind, allowing for the rivets to pull the panels together nicely.
Two seatbelt brackets were given the paint treatment. The square tube bit from the tub centre upright which was found during the big ol’ tidy was derusted, primered, black top coated (to fend off any future galvanic corrosion between the ally upright and the steel bracket) before another coat of primer:
..and fitted to the upright:
The old U-channel removed from the passenger side was used to make a template for the rivet holes into the light cluster. I had some luck here and the drill passed through into the original holes in the panel behind, allowing for the rivets to pull the panels together nicely.
Two seatbelt brackets were given the paint treatment. The square tube bit from the tub centre upright which was found during the big ol’ tidy was derusted, primered, black top coated (to fend off any future galvanic corrosion between the ally upright and the steel bracket) before another coat of primer:
..and fitted to the upright:
Last edited by andrewjsimpson1977 on Sun Jun 02, 2019 10:05 pm, edited 1 time in total.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
..I also started stripping the seat box. One of the two wider supports was badly bent, with the wide section bent upwards somehow and twisted to one side, and one of the two small reinforcements bent downwards away from the wider piece. I didn’t get a ‘before’ photo, but here are both pieces being checked for alignment after straightening:
There's still some bitumastic residue to remove, which I’ll sort tomorrow before the pieces are fixed back together.
..and finally there was time for a bit more mock up work checking panels for straightness, and generally being childish by getting excited at a landy shaped thing. In this photo, you can see that I have replaced the gnarly old chewed up rivets on the drivers side U-channel to match the nice new ones on the opposite side. Tomorrow I’ll probably fit the steering wheel and sit there making Toad of Toad Hall “brrrmm brrrmmm” noises.
That’s it for today, toot toot!
Andy
There's still some bitumastic residue to remove, which I’ll sort tomorrow before the pieces are fixed back together.
..and finally there was time for a bit more mock up work checking panels for straightness, and generally being childish by getting excited at a landy shaped thing. In this photo, you can see that I have replaced the gnarly old chewed up rivets on the drivers side U-channel to match the nice new ones on the opposite side. Tomorrow I’ll probably fit the steering wheel and sit there making Toad of Toad Hall “brrrmm brrrmmm” noises.
That’s it for today, toot toot!
Andy
Re: Monty the rather rusty 2A - 37FG31
Hiya Andy!
Good to see you had a productive day mate, it's coming together nicely.
I had planned on doing some project work yeterday, but spent Saturday hobbling around, and all of yesterday laid up resting a bandaged ankle.
Have fun making brrmmm-brrmmm noises, I'm going to take some more industral strength pain killers and then we'll see if I can get a boot on over the bandage.
Look forwards to your next update, keep the flag flying.
Regards,
Good to see you had a productive day mate, it's coming together nicely.
Have fun making brrmmm-brrmmm noises, I'm going to take some more industral strength pain killers and then we'll see if I can get a boot on over the bandage.
Look forwards to your next update, keep the flag flying.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.