Monty the rather rusty 2A - 37FG31
Re: Monty the rather rusty 2A - 37FG31
Always good to have a spare mate. I looked at it and thought, 'That's an FFR idler bracket.' , then remembered yours doesn't have one of those, but does have a dynamo. And I only thought that as I was looking at the dynamo on Martin's IIA when having a wing lean chat on Saturday.
Regards,
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
No such thing as a day off for the professionals eh Neil. Do you see Lightweight engine bays in your sleep?
So.. after a hasty drive back from visiting my good lady’s family in Staffordshire, this afternoon I got a couple of hours at home on my own. It was one of those times when a long list of ‘to do’ is only chipped into, due to the lateness of the hour and the soreness of the bones. Man I’m tired this week. Must be the system shock from the first couple of weeks back in work.
Aaaanyway, waffling over.. time for photos
First job was to finish cleaning up the two side upright support brackets for the seat back, and get them into primer:
..then rivet them in place. Annoyingly I have misplaced my air riveter, so it was back to the skin pinching joys of the manual gun:
Then it was on to the striker plate reinforcements / stiffeners...
So.. after a hasty drive back from visiting my good lady’s family in Staffordshire, this afternoon I got a couple of hours at home on my own. It was one of those times when a long list of ‘to do’ is only chipped into, due to the lateness of the hour and the soreness of the bones. Man I’m tired this week. Must be the system shock from the first couple of weeks back in work.
Aaaanyway, waffling over.. time for photos
First job was to finish cleaning up the two side upright support brackets for the seat back, and get them into primer:
..then rivet them in place. Annoyingly I have misplaced my air riveter, so it was back to the skin pinching joys of the manual gun:
Then it was on to the striker plate reinforcements / stiffeners...
Last edited by andrewjsimpson1977 on Mon May 27, 2019 9:27 pm, edited 2 times in total.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
...which were cleaned up and primered, and left to dry while I had my dinner. If Sara asks I had a healthy salad, and definitely not a frozen pizza from the petrol station.
Lined up with a bit of wood and some metal shims until the right height was achieved:
After the first couple of holes were drilled it became apparent that access for at least one of the others would be limited round the back
so I grabbed the stiffener
and bolted it through the first two holes to be used as a drilling template.
Next, a quick check using the base bracket for the door striker (Its actually driver’s side one but it was to hand and the hole pattern is identical)
..and finally happy that the bracket was positioned correctly, it was glued and bolted up for a few days to cure:
I also fitted some more rivets, fastening the tub floor front to the valance panel, and the underside of the seat back panel, also to the valance.
I nearly forgot - have also fitted the driver's side dog ear, but then you've seen one of those already. It's coming together nicely - really pleased to see something vaguely truck-shaped appearing from the murky depths of the garage.
That’s it for tonight - I dug out the seat box parts for cleaning up as that will be the next big piece of the jigsaw. It doesn’t look too bad, but I’ll save those photos for another day.
All the best,
Andy
Lined up with a bit of wood and some metal shims until the right height was achieved:
After the first couple of holes were drilled it became apparent that access for at least one of the others would be limited round the back
Next, a quick check using the base bracket for the door striker (Its actually driver’s side one but it was to hand and the hole pattern is identical)
..and finally happy that the bracket was positioned correctly, it was glued and bolted up for a few days to cure:
I also fitted some more rivets, fastening the tub floor front to the valance panel, and the underside of the seat back panel, also to the valance.
I nearly forgot - have also fitted the driver's side dog ear, but then you've seen one of those already. It's coming together nicely - really pleased to see something vaguely truck-shaped appearing from the murky depths of the garage.
That’s it for tonight - I dug out the seat box parts for cleaning up as that will be the next big piece of the jigsaw. It doesn’t look too bad, but I’ll save those photos for another day.
All the best,
Andy
Re: Monty the rather rusty 2A - 37FG31
Have you thought about using countersunk pop rivets for the wheelbox to side channel? Once paint is on tub they are far less noticeable than standard pop rivets.
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
I did give it some thought, but as I didn’t have any in stock I went with what I had. The more I think about it the more you may be right - can always swap them out before paint.
Re: Monty the rather rusty 2A - 37FG31
Hello andrewjsimpson1977,
I am impressed by your work and the quality of it.
You are leaving very far, congratulations for your approach.
Receive all my congratulations and encouragement.
Looloo
I am impressed by your work and the quality of it.
You are leaving very far, congratulations for your approach.
Receive all my congratulations and encouragement.
Looloo
27GJ77 - 1977 LWT SIII FFR - 1st. Royal Horse Artillery - B Battery (BAOR)
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
Andy,
Looking very good. If my seat back panel wasn't being remade we would be having a race to the finish of the tub.....and I know where my air riveter is
Looking very good. If my seat back panel wasn't being remade we would be having a race to the finish of the tub.....and I know where my air riveter is
1965 Series IIA 88" 200tdi
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]
1968 Series IIA LWT 12v GS RHD [34-FG-95]
1976 Series III LWT 24v FFR RHD [45-GF-53]
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
You might have some other competition soon - Mac is having his seat back panel remade too. Let battle commence!
-
andrewjsimpson1977
- Cake Guru
- Posts: 3613
- Joined: Tue Aug 11, 2015 3:31 pm
- Location: Befordshire
Re: Monty the rather rusty 2A - 37FG31
A few more pictures - first a spot of mock-uppery to see how things were aligning and what needs work to get straight:
...well ok yes and it made me feel like I had a truck shaped thing again. It does annoy me to see the land rover badge on the wrong side - that'll be getting fixed soon enough.
Next I finished straightening the centre upright support and got it in some etch primer:
..before fitting to the valance panel:
I just wish I could remember what I did with the square tube section which receives the uber-rare long pole for the tub passengers to cling onto when in airportable mode. I feel another garage tidy coming on.
I really am out of rivets now, so until some more turn up (hopefully Friday) I’ll have to find something else to do. I did find the timing indicator for the front engine panel, so that will get un-bent and fitted tomorrow time permitting. I should then be able to work out how to get a basic static timing job done on the engine.
Evening all,
Andy
...well ok yes and it made me feel like I had a truck shaped thing again. It does annoy me to see the land rover badge on the wrong side - that'll be getting fixed soon enough.
Next I finished straightening the centre upright support and got it in some etch primer:
..before fitting to the valance panel:
I just wish I could remember what I did with the square tube section which receives the uber-rare long pole for the tub passengers to cling onto when in airportable mode. I feel another garage tidy coming on.
I really am out of rivets now, so until some more turn up (hopefully Friday) I’ll have to find something else to do. I did find the timing indicator for the front engine panel, so that will get un-bent and fitted tomorrow time permitting. I should then be able to work out how to get a basic static timing job done on the engine.
Evening all,
Andy