Monty the rather rusty 2A - 37FG31

Tell us about any of your Land Rover related projects here.
andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Dec 30, 2018 4:14 pm

chipbury wrote: ↑
Sun Dec 30, 2018 9:54 am
Looks very tub shaped, well done - are you going to use Cleco pins (and the setting tool) to assist with the riveting?
Probably more like the time honoured nuts and bolts until ready to rivet approach Chris, as I have plenty of those to hand.

So today I cut the excess material out of the new U-channel so it would slot in against the rear light cluster section..

A52E6202-CA24-49E0-A781-5A027A4EF293.jpeg
A52E6202-CA24-49E0-A781-5A027A4EF293.jpeg (1.06 MiB) Viewed 2462 times

Firstly the little diagonal needed cutting at the corner of one end..

BA30075E-0D1E-4983-97F9-E7392B47B5F3.jpeg
BA30075E-0D1E-4983-97F9-E7392B47B5F3.jpeg (1.18 MiB) Viewed 2462 times
A1BE9C09-ADEF-40C3-8B94-D191959156A8.jpeg
A1BE9C09-ADEF-40C3-8B94-D191959156A8.jpeg (1.15 MiB) Viewed 2462 times

Then the cutaway for the rear light cluster..

8FD99233-B0EA-4F6B-A3A9-1584BC140D87.jpeg
8FD99233-B0EA-4F6B-A3A9-1584BC140D87.jpeg (966.52 KiB) Viewed 2462 times

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Dec 30, 2018 4:18 pm

Out with the snips again..

18D5888C-42AE-4716-B7C3-D7BB826D4EE6.jpeg
18D5888C-42AE-4716-B7C3-D7BB826D4EE6.jpeg (841.5 KiB) Viewed 2462 times

Smooth off the cut edges with the flappy wheel bobbin thing..

4E70448A-5185-430B-8C91-48F9C435CE12.jpeg
4E70448A-5185-430B-8C91-48F9C435CE12.jpeg (1013.52 KiB) Viewed 2462 times

..and a test fit. Went in first time. Hooray.

FE414C23-877C-411E-86DB-652BD97F423B.jpeg
FE414C23-877C-411E-86DB-652BD97F423B.jpeg (942.48 KiB) Viewed 2462 times
0279CB94-2F65-4730-A305-6857E846BE9B.jpeg
0279CB94-2F65-4730-A305-6857E846BE9B.jpeg (932.41 KiB) Viewed 2462 times

That just leaves the last little update..

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Dec 30, 2018 4:26 pm

... the trumpet section.

I dug out the lock tab washer thing from the original, and both have had a clean up, de-rust, anti rust primer and a good coat of black top coat.

8DD52F87-1D38-4A64-8CBF-D3A1283DC350.jpeg
8DD52F87-1D38-4A64-8CBF-D3A1283DC350.jpeg (901.15 KiB) Viewed 2462 times

(..and yes that’s my scalectrix, what of it? I refuse to fully grow up on account of it being overrated)

Andy

Oneandtwo
Posts: 242
Joined: Sun Nov 09, 2014 7:53 am

Re: Monty the rather rusty 2A - 37FG31

Post by Oneandtwo » Mon Dec 31, 2018 8:06 am

Are you going to fit the lower seatbelt mountings?

I fitted brand new old stock genuine lower tub channels in 2006. They had already rotted through where the seatbelt reinforcing plates were by 2014, and that was with copious paint and waxoyl. This time around I left them out as I only used the upper seatbelt mountings anyway.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Mon Dec 31, 2018 8:14 am

I was thinking the same to be honest, at least for now.

The plan of to be ready for W&P, so right to the back of the queue go all non essentials. Airportable configuration additional seatbelt mountings, convoy lamp, yellow bridging plate, clip in radio... anything that will slow me down has to go.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Fri Jan 04, 2019 5:45 pm

A couple of bits to report on:

The remnants of the tub frame has been soaked in paraffin (the rags help to keep it on the surface rather than running off), to get rid of the last of the bitumastic. You can see the bitumen soaking into the rag - it’s really effective if quite a slow process. It took about 3 hours of repeated soaking and fresh rags, and I would still like to give it a final clean with white spirit tomorrow to be totally happy.

A1EEC822-6D6D-4C22-A23D-CC7E4D39E6B1.jpeg
A1EEC822-6D6D-4C22-A23D-CC7E4D39E6B1.jpeg (1.69 MiB) Viewed 2402 times
A7AF0E1C-003F-4610-8E84-9C1B372E1213.jpeg
A7AF0E1C-003F-4610-8E84-9C1B372E1213.jpeg (1.52 MiB) Viewed 2402 times

Removing the underseal has also revealed a couple of small dents which will be tapped back to flat in the morning. I’m also happy to report the rivets have arrived for the first few bits of the tub rebuild, so hopefully I can get the floor and front valance panel fastened in sometime next week.

Also, I won a couple of bonnet strap mounts cheap on eBay which were mislabelled as tub tie downs:

28C14375-3328-4BA6-8BA6-4A545175A797.jpeg
28C14375-3328-4BA6-8BA6-4A545175A797.jpeg (865.94 KiB) Viewed 2402 times

I need to find a third (if anyone has one spare I’ll happily exchange for beer tokens) to complete the set. I need the centre staple too, but suspect that might be one for the stalls at this year’s shows.


That’s it for now,

Andy

User avatar
Bob Fell
Cake Guru
Posts: 3044
Joined: Wed Sep 18, 2013 7:17 am
Location: Melton Mowbray

Re: Monty the rather rusty 2A - 37FG31

Post by Bob Fell » Fri Jan 04, 2019 6:35 pm

Nice work Andy :D
Bob
042Bobf


19HF27 Lightweight FFR ex Gurkha Field Force HQ, various Gurkha Sigs Tps and Comp Ord Depot Hong Kong 1980-1997.
42ET39 Narrow Track Sankey ex BAOR 22 & 7 Sig Regts, 16/5 Lancers, 2 RTR, 9/12 Lancers & QDG 1969-2001.

chipbury
Master Baker
Posts: 1411
Joined: Sun Oct 02, 2011 3:26 pm
Location: Bath

Re: Monty the rather rusty 2A - 37FG31

Post by chipbury » Sat Jan 05, 2019 6:50 pm

Is the John Deere tractor a future project?
2A - 39 FG 70

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sun Jan 06, 2019 4:54 pm

chipbury wrote: ↑
Sat Jan 05, 2019 6:50 pm
Is the John Deere tractor a future project?
It might become the current project if I have to spend much longer cleaning bits of bitumastic off the lightweight tub :evil: :x

Another three hours of scrubbing and binning piles of white spirit and black gunk soaked rags - and it still bloody needs more!! Next weekend we are taking the kids for a 'surprise' weekend away, so at least I get a break of nearly two weeks from the horrible jobs. I will still tinker in the meantime - there are bits in the post which should bolt straight on to the engine / chassis, but thats quite enough of the black stuff for now.

All the best,

Andy

chipbury
Master Baker
Posts: 1411
Joined: Sun Oct 02, 2011 3:26 pm
Location: Bath

Re: Monty the rather rusty 2A - 37FG31

Post by chipbury » Sun Jan 06, 2019 7:58 pm

You make me feel inferior as I left all the black stuff on!
2A - 39 FG 70

Post Reply