Monty the rather rusty 2A - 37FG31

Tell us about any of your Land Rover related projects here.
MickB
Posts: 17
Joined: Sun Sep 04, 2016 9:50 pm
Location: Northants

Re: Monty the rather rusty 2A - 37FG31

Post by MickB » Fri Dec 21, 2018 5:19 pm

Cheers Andy :!

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Fri Dec 28, 2018 5:57 pm

Getting twitchy over the Christmas break so today I stripped the gearbox tie bar down and refurbed with a bit of paint and new rubber bushes. Table cloth hurriedly thrown in the wash before it was missed :D

22E0D4D8-00D6-40DB-A915-0F045434F4C4.jpeg
22E0D4D8-00D6-40DB-A915-0F045434F4C4.jpeg (1.37 MiB) Viewed 2357 times

The old bushes were shot, particularly on the gearbox end where they had started to break up into cracked chunks of rubber.

17F7B7DB-D496-4AE2-A46A-B8E781E37BA3.jpeg
17F7B7DB-D496-4AE2-A46A-B8E781E37BA3.jpeg (1.46 MiB) Viewed 2357 times

Lovely new bushes courtesy of Craddocks..

423E5449-1E68-4733-BD85-22B5D042B578.jpeg
423E5449-1E68-4733-BD85-22B5D042B578.jpeg (954.44 KiB) Viewed 2357 times

The finished article. It’s too dark / damp outside but I’ll get it fitted in the morning.

786B6657-E758-4B0B-89A5-AE8C3D450226.jpeg
786B6657-E758-4B0B-89A5-AE8C3D450226.jpeg (766.24 KiB) Viewed 2357 times

Tomorrow I’ll also be drilling the first holes in the shiny new seat back bulkhead :?

All the best,

Andy

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Monty the rather rusty 2A - 37FG31

Post by removeduser185 » Fri Dec 28, 2018 10:11 pm

I hope you had a good Christmas. Nice to get back into the garage, though. And another piece done, a step along the way. I am waiting for a new ignition switch - I shall then re-do my interior light wiring and hope everything else is OK. Looking forward to getting that done. Keep the reports comng - it's all a bit quiet on here at the moment. We need Neil's project to start up again.

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Monty the rather rusty 2A - 37FG31

Post by AR4412 » Sat Dec 29, 2018 10:16 am

Hiya Fred! :D ,

Hopefully the new year brings a new start, well, fingers crossed. The chassis will be on hold until the warmer weather arrives, but I might be able to make a start on some of the stowage bits at last. Santa did bring me some steel and two boxes of butt hinges. :D

I hope you get all the holes in the right place Andy, none in your arms or legs would be a good start. :P

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sat Dec 29, 2018 1:03 pm

Fred - I was thinking the same, thankfully by the sound of things the Recce drought will soon be a memory, and we’ll all get our Sundays back.

Neil - I have now got a mostly operational thumb, and a new cordless drill to hold with it, so who knows what harm I can do to myself in the coming days :D

So far today I have been skirting around the main event, by fitting some earthing straps, and adjusting and bolting on the gearbox steady bar (one of the holes doesn’t line up, I think because the gearbox is a 252 prefix type, so I’ll need to redrill the bracket at some point). I also re-routed one of the flexi oil pipes as I wasn’t happy with how it lined up with the hard pipe to the driver’s side of the oil cooler. All good now.

I’ve been looking at the old seatback, dog ears and front tub balance thingy to see how it all should line up. Nothing too drastic (famous last words) and as a sanity check, the new dog ears line up with the marks on the old seat back panel and vice versa.

I’ll pop out in a half hour or so and try to get a photo of the basic alignment.

Andy

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sat Dec 29, 2018 2:10 pm

Alright so that went a lot better than expected. I sometimes overcook problems in my head before realising there’s nothing to stress about, and this was definitely a prime example. Last night I drew up some plans on the back of a post-Christmas cardboard box, and was wondering how I was going to know everything would line up correctly.

Well I needn’t have bothered, as it turns out that while Land Rover had a talent for making things awkward to put together, for once they had applied some good old fashioned engineering nouse and made the tub so it all only goes together one way.

The remanants of the old frame (minus one u-channel) were stood up against the shed, with the new balance panel offered up to add some rigidity:

59903E15-CFB0-4E05-ADCD-D5E7FAE40F52.jpeg
59903E15-CFB0-4E05-ADCD-D5E7FAE40F52.jpeg (1.1 MiB) Viewed 2306 times

Go fetch the floor, pop the valance off, slide in the floor and tap the valance panel back on. The floor has three ‘slots’ where the top hat sections are lifted away from the underside of the main floor panel. These allow the lip in the balance panel to be slotted in, and the fit is tight enough that the whole thing holds together nicely. A bit of a tap from one end and the holes in the frame, floor and valance line up perfectly. Nice.

5E988FF6-B256-4E49-9C1C-3B86D8B9DD86.jpeg
5E988FF6-B256-4E49-9C1C-3B86D8B9DD86.jpeg (834.05 KiB) Viewed 2306 times

Add seatback panel. This is where I thought I would struggle. Being a brand new panel from the local fabricators, it doesn’t have any holes or markings. I did still have the original though, from which it’s obvious that the valance sits underneath the lip of the seatback. There is no other way it fits, and if lined up evenly side to side, it’s easy to see that all the tangs / lips on the rest of the tub will mate up with it nicely.

Finally, pop the dog ears on and even the holes in the side of the tub line up. What’s the catch?!? I’m deeply distrustful of the universe at the best of times. Surely it can’t be that easy? BUT. BUT ITS A LAND ROVER!!!

3539DA9A-0543-415F-BFF7-909401807612.jpeg
3539DA9A-0543-415F-BFF7-909401807612.jpeg (1.23 MiB) Viewed 2306 times

F15DFFCF-C8C7-4FEB-ACD2-5C6D0B77FC47.jpeg
F15DFFCF-C8C7-4FEB-ACD2-5C6D0B77FC47.jpeg (1.25 MiB) Viewed 2306 times

You can see from the last photo that the replacement U-channel isn’t on yet. It needs trimming at the rear end in order to fit around the light cluster section. I also need to straighten up the lip it fastens to, as it got a bit bent when I was drilling / prising out the old spotwelds.

I am absolutely made up about this progress. Yes there are lots of bits to do even assuming all this was finally riveted together. For starters I have to clean off some more underseal from the old tub sections, and there are the strengtheners for behind the seatback to glue and river in place. Then there’s the paint, tub runners etc zzzzzzz. But come on - it’s tub shaped!!

Anyway, with my newfound confidence in everything fitting, I can’t be bothered to drill anything now. Sod it, I’ll do it after the tub bits are clean enough to be stuck together for good.

All the best,

Andy

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: Monty the rather rusty 2A - 37FG31

Post by removeduser185 » Sat Dec 29, 2018 4:14 pm

That is looking brilliant! Real progress. Do you have an air riveter? I didn't, but subsequently discovered that they're dirt cheap and make very light work of pop riveting. Worth considering if you have a compressor.

And Neil - just start photographing things -anything at all (Land Rover shaped) to get your thread going again.

andrewjsimpson1977
Cake Guru
Posts: 3613
Joined: Tue Aug 11, 2015 3:31 pm
Location: Befordshire

Re: Monty the rather rusty 2A - 37FG31

Post by andrewjsimpson1977 » Sat Dec 29, 2018 4:31 pm

I do have one Fred and yes was planning on enjoying the lack of sore hands when putting the tub together properly.

Neil mate, Ian’s idea is a good one no? You could post photos of the bits you know are finished, but no one else does :twisted:

Andy

chipbury
Master Baker
Posts: 1411
Joined: Sun Oct 02, 2011 3:26 pm
Location: Bath

Re: Monty the rather rusty 2A - 37FG31

Post by chipbury » Sun Dec 30, 2018 9:54 am

Looks very tub shaped, well done - are you going to use Cleco pins (and the setting tool) to assist with the riveting?
2A - 39 FG 70

Landie68
Master Baker
Posts: 1564
Joined: Sat Dec 03, 2016 6:31 pm
Location: Herefordshire

Re: Monty the rather rusty 2A - 37FG31

Post by Landie68 » Sun Dec 30, 2018 12:17 pm

Nice to see progress again Andy, even if it's only a dry run.
Regards
Richard

Discovery Sport
15FM83 ex 15 Para and 7 PO's

Post Reply