FM, What have I done project
Re: FM, What have I done project
Well we are making progress. Back axle off and looking useful.
Some questions if you don't mind.
What size brake pipe spanner?
Not sure whether to get axle blasted or just flappy disk then Buzzweld primer.
If I get it blasted should I strip out all the innards first?
Stripping the front looks more involved than the rear which is why I started at the back end.
What is the best series of steps to follow
Presumably I Will have to separate the engine from the gearbox to get those out? All I have lifting wise is an old fore end loader. Have thought of may be putting her on her nose!.
Other than you chaps I also have the local bank to thank for the supply of coin bags which are ideal for all the various small bits and bobs.
Some questions if you don't mind.
What size brake pipe spanner?
Not sure whether to get axle blasted or just flappy disk then Buzzweld primer.
If I get it blasted should I strip out all the innards first?
Stripping the front looks more involved than the rear which is why I started at the back end.
What is the best series of steps to follow
Presumably I Will have to separate the engine from the gearbox to get those out? All I have lifting wise is an old fore end loader. Have thought of may be putting her on her nose!.
Other than you chaps I also have the local bank to thank for the supply of coin bags which are ideal for all the various small bits and bobs.
- Attachments
-
- IMG_3383.JPG (888.23 KiB) Viewed 1632 times
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
- removeduser185
- Cake Guru
- Posts: 3531
- Joined: Thu Jun 18, 2015 10:37 pm
Re: FM, What have I done project
Oh my goodness, yes, quite a bit of rust there. I have never stripped a Land Rover before, in fact apart from changing an engine on my Morris Marina a year or two ago, my practical knowledge of car restoration is very limited. But, Land Rovers are only large Meccano sets, so, if you have good manuals anything is possible. So: you need the Series III Repair Operations Manual to start with. Then you need copies of both the Series III Illustrated Parts Catalogue (IPC) and the IPC for the Lightweight. Brooklands will have copies of these. I actually have a copy of the IPC fiche for the Lightweight as well because all three IPCs will differ in some detail - some bits in the Lightweight IPC are simply wrong - the illustration of the chassis for a start (it is of a standard civilian pattern not the Lightweight one with the fixed front cross-member) and it also shows other things which aren't on a Lightweight, such as the panel between the front bumper and the grille! You also need a facsimile of the user handbook (also from Brooklands) and then a copy of the servicing schedule. So, you do need to browse these books a great deal (I spend hours in the evenings with these and also with Mark Cook's book as this will illustrate a wide range of Lightweights so you can start to build up a knowledge of the different modifications etc). The James Taylor/Geoff Fletcher book is another useful tome. As for tools, well, if original most of your nuts and bolts should be imperial and the most common sizes seem to be 7/16" and 9/16" (brake pipe spanner size) so you want a couple of each of those as well as sockets. You seem to be pretty good at removing the heavy bits and, as you work forward it will get easier as there will be more oil over everything. I have a long piece of old steel tube which fits over the end of all my spanners as it helps undoing (or shearing off) rusted nuts, but that's arthritis for you!
With what work you have left, I would go for taking things off in this order: bonnet, front wings, grille panel, oil cooler, radiator, front wiring loom, pedal boxes, then the bulkhead. Once that is off, you can strip off the steering and get to the engine and gearbox easily as well as the remaining brake lines and so on. Whether you then take the gearbox and engine off separately is up to you. I haven't done that yet and am undecided. My neighbour (a car restoration pro) suggests it is easier to take both off together and then split them once on the bench/floor, but that also assumes you have enough room to do that comfortably.
I'm not getting anything blasted as I don't have access to the facilities, but I don't think it advisable to blast an axle with all the gubbins inside, - it'll be too heavy, blasting medium will get everywhere and possibly damage things. Does it really need blasting? After all you aren't looking for a mirror finish when its painted anyway. However, I am speaking as a novice, working for the first tie in my own garage. There are people on here with far greater experience than mine so, wait until you have a few more pieces of advice before you dive in. And enjoy!
Best
Fred
With what work you have left, I would go for taking things off in this order: bonnet, front wings, grille panel, oil cooler, radiator, front wiring loom, pedal boxes, then the bulkhead. Once that is off, you can strip off the steering and get to the engine and gearbox easily as well as the remaining brake lines and so on. Whether you then take the gearbox and engine off separately is up to you. I haven't done that yet and am undecided. My neighbour (a car restoration pro) suggests it is easier to take both off together and then split them once on the bench/floor, but that also assumes you have enough room to do that comfortably.
I'm not getting anything blasted as I don't have access to the facilities, but I don't think it advisable to blast an axle with all the gubbins inside, - it'll be too heavy, blasting medium will get everywhere and possibly damage things. Does it really need blasting? After all you aren't looking for a mirror finish when its painted anyway. However, I am speaking as a novice, working for the first tie in my own garage. There are people on here with far greater experience than mine so, wait until you have a few more pieces of advice before you dive in. And enjoy!
Best
Fred
Re: FM, What have I done project
Hi Mac,
Seeing as you have gone this far I would strip the axle completely (good practice to start on the rear one!).
It is worth changing the hub seal running faces on the two stub axles whilst everything is apart - parts required will be
599698 distance piece x 2
500978 gasket rear stub axle to rear axle x 2
251322 nut 3/8" UNF x 12
576521 bolt 3/8" UNF x 12
You might as well remove the diff as well and change the gasket on that (at some point the diff input seal will need doing as well!).
7316 differential gasket
NH606041L nut differential x 10
As for cleaning/painting I stripped mine and had the casings blasted before I repaired the strengthening strips. It's a pain to clean the debris out of the axle casings so may be easier to use a flap disc to clean them up yourself.
Have fun!
Seeing as you have gone this far I would strip the axle completely (good practice to start on the rear one!).
It is worth changing the hub seal running faces on the two stub axles whilst everything is apart - parts required will be
599698 distance piece x 2
500978 gasket rear stub axle to rear axle x 2
251322 nut 3/8" UNF x 12
576521 bolt 3/8" UNF x 12
You might as well remove the diff as well and change the gasket on that (at some point the diff input seal will need doing as well!).
7316 differential gasket
NH606041L nut differential x 10
As for cleaning/painting I stripped mine and had the casings blasted before I repaired the strengthening strips. It's a pain to clean the debris out of the axle casings so may be easier to use a flap disc to clean them up yourself.
Have fun!
2A - 39 FG 70
Re: FM, What have I done project
Thanks for the helpful list Chip,chipbury wrote:Hi Mac,
Seeing as you have gone this far I would strip the axle completely (good practice to start on the rear one!).
It is worth changing the hub seal running faces on the two stub axles whilst everything is apart - parts required will be
599698 distance piece x 2
500978 gasket rear stub axle to rear axle x 2
251322 nut 3/8" UNF x 12
576521 bolt 3/8" UNF x 12
You might as well remove the diff as well and change the gasket on that (at some point the diff input seal will need doing as well!).
7316 differential gasket
NH606041L nut differential x 10
As for cleaning/painting I stripped mine and had the casings blasted before I repaired the strengthening strips. It's a pain to clean the debris out of the axle casings so may be easier to use a flap disc to clean them up yourself.
Have fun!
As raining today I will order up the parts. wonder if spraying old oil through the stripped casing would help clean out the rubbish. Probably safer than using someone's feather duster!
Mac
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
Re: FM, What have I done project
Thanks for the pointers Fred. All fired up to get going this morning but it's raining and it is outside and I am worried about rust!
A chum is lending me again the 7/16 and 9/16 spanners. Must get me own.
Undecided on which route to go (blast or flappy) though prefer the flappy option though with my limited knowledge inclined to take unscripted axle to be blasted as can't see that it will cause any damage to the workings and then refurb. Or will it?
Lucky to have a blaster within a mile or two.
Mac
A chum is lending me again the 7/16 and 9/16 spanners. Must get me own.
Undecided on which route to go (blast or flappy) though prefer the flappy option though with my limited knowledge inclined to take unscripted axle to be blasted as can't see that it will cause any damage to the workings and then refurb. Or will it?
Lucky to have a blaster within a mile or two.
Mac
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
Re: FM, What have I done project
The safest option for blasting would be to make three blanks to go over the ends/diff faces (plywood etc). Bolt them on using the old nuts and it should keep the blasting media out. Don't forget to put the drain plug in and leave an old vent on.
You could reuse the blanks for the front casing later.
You could reuse the blanks for the front casing later.
2A - 39 FG 70
Re: FM, What have I done project
My plan was to strip the axles down for blasting, but leave the diffs in as I want them blasted too, and blank off the ends of the axle casings to stop the media getting in there.
I'm getting too old for loading an complete axle into the back of a Land Rover on my own, especially a front axle, so I will take the diffs out for loading/unloading and bolt them back in at the blasters.
Regards,
I'm getting too old for loading an complete axle into the back of a Land Rover on my own, especially a front axle, so I will take the diffs out for loading/unloading and bolt them back in at the blasters.
Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
'First my weapon. Then my equipment. Then myself.'
Neil.
09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.
Re: FM, What have I done project
Sounds like a plan chaps, thanks.
Stopped raining so I thought why not.
So a little petrol in the carb a fiddle here and there and off she went.
Mac
Stopped raining so I thought why not.
So a little petrol in the carb a fiddle here and there and off she went.
Mac
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
Re: FM, What have I done project
Hello All,
These dome heads hold the front wings to the triangular panel from the side of the bulkhead and look a bit special to me. They fix into the type of four sided captive nut that is enclosed in thin metal. Obviously I have no idea what they are called and more importantly are these dome heads really that special. They appear to be of two parts.
Anyone got a spare bar for a lj263 jack? Sale, swap or otherwise.
Mac
These dome heads hold the front wings to the triangular panel from the side of the bulkhead and look a bit special to me. They fix into the type of four sided captive nut that is enclosed in thin metal. Obviously I have no idea what they are called and more importantly are these dome heads really that special. They appear to be of two parts.
Anyone got a spare bar for a lj263 jack? Sale, swap or otherwise.
Mac
- Attachments
-
- IMG_3441.JPG (887.62 KiB) Viewed 1566 times
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
Re: FM, What have I done project
Hello there,
Please tell me know one extracts the hella flasher from the dash panel. It works so rather not break it to find out.
Also the sensor wires for the oil and water gauges. These appear to screw in to the rear. A gentle twist with pliers does little and again rather not risk breaking them, mind you dials look pretty stuffed tbf.
Front wings removed, front panels, oil cooler, air filter and rad removed. Headlights stripped of usable bits rest is a mix of three quarter circles but not chucking away. Cheers Fred and all for the advice.
Lastly, anyone got a spare threaded female bit on the back of a NATO socket, presumably holds all the connectors in place. Sell swap barter or pointers on where to get one.
Mac.
Please tell me know one extracts the hella flasher from the dash panel. It works so rather not break it to find out.
Also the sensor wires for the oil and water gauges. These appear to screw in to the rear. A gentle twist with pliers does little and again rather not risk breaking them, mind you dials look pretty stuffed tbf.
Front wings removed, front panels, oil cooler, air filter and rad removed. Headlights stripped of usable bits rest is a mix of three quarter circles but not chucking away. Cheers Fred and all for the advice.
Lastly, anyone got a spare threaded female bit on the back of a NATO socket, presumably holds all the connectors in place. Sell swap barter or pointers on where to get one.
Mac.
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.