FM, What have I done project

Tell us about any of your Land Rover related projects here.
Post Reply
Macvfork
Pastry Chef
Posts: 717
Joined: Sun Aug 17, 2014 3:31 pm
Location: Heathfield, sussex

FM, What have I done project

Post by Macvfork » Sun Oct 09, 2016 8:26 am

Morning All,
Thanks for all the advice and encouragement regarding the unexpected purchase of a crock.
Stripping underway and plenty of photos taken - the pile of rust gets bigger but storage space diminishing due in part to collecting stuff I think I need.

Trouble is:
I do not know if a civilian series 3 front bulk head is identical to an S3 lwt bulkhead.
Vent panel is the early type with Trico bottle to the right of the steering wheel. Need a replacement vent panel.
Need a chassis but do not know if there is any difference between a late one or early S3 chassis but know the difference between mil and civvie.
I don't know at what point With axles are they beyond reuse? Have read that in some cases the casing is kaput but reasons why not given. It's gotta hold ep90 for a start I guess.

Spinning of the back hubs does not result in prop shaft movement which indicates an issue there unless I am mistaken.

All advice, banter etc much appreciated - knowledge and a laugh will enriched the experience.

Thanks
Mac
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.

Macvfork
Pastry Chef
Posts: 717
Joined: Sun Aug 17, 2014 3:31 pm
Location: Heathfield, sussex

Re: FM, What have I done project

Post by Macvfork » Sun Oct 09, 2016 8:45 am

Forgot to say...
Presumably a new loom would be sensible though from what I have seen so far the original does not seem brittle.
Who would you recommend?

Apologies for the barrage of questions.

Not raining today so should be able to make some more progress.

Mac
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.

User avatar
StuWright
Master Baker
Posts: 1740
Joined: Wed Feb 24, 2016 11:10 pm
Location: Southampton

Re: FM, What have I done project

Post by StuWright » Sun Oct 09, 2016 10:04 am

Hi Mac as far as I'm aware the Lwt bulkhead, vent panel etc are different to the civvy ones. Vent panels are a pain to get hold of and not cheap. I had to have mine rebuilt by Ashtree who make bulkheads.

Early chassis should be the same as later S3. I have a S2A body and because the log book is S3 I ordered a half S3 chassis from Richards Chassis. I had no idea if there were differences and it all fitted fine.

I have a new loom from Autosparks which just gave me peace of mind that the wiring would be correct after putting it back together. I'm doing a Tdi swap but they do complete standard looks for the let which include the 6 way switch wiring.

3 years ago mine was a chassis and a pile of corroded panels and incorrect parts, so never feel it won't come together in the end. I'm still asking tons of questions every week and this is the place to get friendly expert advice. ;)
Thanks

Stu

55AM52 Ex RAF Land Rover Lightweight GS

User avatar
removeduser185
Cake Guru
Posts: 3531
Joined: Thu Jun 18, 2015 10:37 pm

Re: FM, What have I done project

Post by removeduser185 » Sun Oct 09, 2016 10:24 am

Macvfork wrote: I do not know if a civilian series 3 front bulk head is identical to an S3 lwt bulkhead.

Need a replacement vent panel.

Need a chassis

I don't know at what point With axles are they beyond reuse?

Spinning of the back hubs does not result in prop shaft movement which indicates an issue there unless I am mistaken.

Mac
As Stu says, the civilian bulkhead is very different - side profile, of course as the Lightweight has no hips! And it incorporates the vent panel whereas that on the Lightweight is a separate piec as you wil have discovered already. The Lightweight bulkhead is a very simple piece of metal, basically three sides of a square: 2 A pillars and a scuttle, filled in with foot-wells and a dashboard. If you are good at welding, it may be repairable. Otherwise, Ashtree can do you a galved reconditioned bulkhead, vent panel and chassis. But don't get rid of anything until you are sure you don't need it and, even then, put it on eBay as it might be useful to someone out there. Can't help with axles, though I would have thought it unlikely the casings are beyond use and the front diff shouldn't be too worn, the half shaft are probably OK as well as stub axles etc, so, strip down and see what you have left - probably more of value than you think. Again, are you sure the chassis is beyond redemption? Usually because land Rovers leak oil, the front end will be pretty solid, even if the rear is lacy - and 1/4 chassis are available, as are outriggers etc. Keep at it,

Best

Fred

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: FM, What have I done project

Post by AR4412 » Sun Oct 09, 2016 12:32 pm

Hi Mac,

I'm not entirely sure of all the chassis differences but there are a few. The SIIA chassis has different front brake hose bracket arrangement from the SIII, that I do know, there's bound to be others. The early SIII chassis doesn't have re-inforced front dumb irons, the later chassis does, it also has holes in the dumb irons for fitment of a steering damper bracket IIRC.

The GS and FFR chassis are different as the GS has four mountings for the air filter/battery box tray and the FFR only has three for the air filter. The later FFR chassis has two mounting brackets for the shunt box on No.4 crossmember that the earlier FFR and the GS chassis doesn't have.

I can't remember if all chassis have the mounting points for the oil cooler on No.2 crossmember as I've only owned FFR's.

There are IIRC three different vent panels. SIIA with the flat windscreen brackets, washer pump bracket in the centre, a flat plate on the left for the wiper motor and on the right for the washer bottle. The SIII has an early and a late type vent panel. The winscreen mountings are a block type as opposed to the SIIA's flat plates. They have only the wiper motor mounting plate on the left side, the early vent panels have holes in them for the washer jets where as the later vent panels do not have these holes as the washer jets were moved to the bonnet. I think I got that right. The good news is that any vent panel will fit and can be modified to look like the one that should be on there.

When checking the rear axle/differential by turning one wheel, was the handbrake applied? If the propshaft is fitted and the handbrake is applied turning one wheel/hub should result in the opposite one turning in the other direction if the half shafts/diff internals are okay. Turning the propshaft/diff input flange should result in both wheels/hubs turning. The only other axle case problems are the possibility of a bent case, front usually if it has had a heavy landing, or rusting out of the diff pan if it's sat with water/watery oil inside.

Good luck with the project, almost anything can be repaired given enough time and patience. I'm surprised at how little I have had to replace during the refurb of my project.

Don't be afraid to ask questions if you're unsure of anything, even if the question does sound like it should have a simple answer. If you don't know, you don't know, and it's best to ask rather than make a silly or expensive mistake. There are plenty of knowledgeable folk on here who will be willing to help, and they won't extract the urine if you ask a seemingly simple question.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

User avatar
StuWright
Master Baker
Posts: 1740
Joined: Wed Feb 24, 2016 11:10 pm
Location: Southampton

Re: FM, What have I done project

Post by StuWright » Sun Oct 09, 2016 1:09 pm

That answers a question for me Neil because I have a bracket part in the middle of my vent panel and read some had a manual washer pump on them. That makes sense as the rest of my panels are 2a. :)
Thanks

Stu

55AM52 Ex RAF Land Rover Lightweight GS

Macvfork
Pastry Chef
Posts: 717
Joined: Sun Aug 17, 2014 3:31 pm
Location: Heathfield, sussex

Re: FM, What have I done project

Post by Macvfork » Sun Oct 09, 2016 6:51 pm

Thanks All. Need to re read and digest.
Did someone ask about differences bt Lwt bulk heads and civvie ones? Silly me one has no hips and a separate vent panel. Lol.

The existing loom is printed up nicely and yellowish but I have an odd wire with the same yellowish outer. It runs rhs from the A pillar, along sill into upper section of tub above and passed wheel arch where it pops out vertically as if to go into the upper removable section. Helpfully nothing attached either end. Any clues? I have number plate wire coming from same area as for light fittings.

Tub removed by rather unorthodox method. 8 bolts or should that be screws rear of seat box? Four slotted dome heads either side and that was it along with a couple of bits of chassis.
Attachments
IMG_3343.JPG
IMG_3343.JPG (777.13 KiB) Viewed 3303 times
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.

User avatar
StuWright
Master Baker
Posts: 1740
Joined: Wed Feb 24, 2016 11:10 pm
Location: Southampton

Re: FM, What have I done project

Post by StuWright » Sun Oct 09, 2016 7:08 pm

Don't worry too much if you have wires which are not the correct colour. I Identified a wire on a mates series last week by process of elimination and found it had been replaced with a different colour. The wiring diagrams are good but not always that accurate after 40 years of repairs. :lol:
Thanks

Stu

55AM52 Ex RAF Land Rover Lightweight GS

Macvfork
Pastry Chef
Posts: 717
Joined: Sun Aug 17, 2014 3:31 pm
Location: Heathfield, sussex

Re: FM, What have I done project

Post by Macvfork » Sun Oct 09, 2016 7:14 pm

Thanks All.
Tubs off, only eight hex screws from rear seat box and 8 slotted dome heads. Wherever it was fixed chassis wise that came too.
Looks pretty good to me.
mac
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.

Macvfork
Pastry Chef
Posts: 717
Joined: Sun Aug 17, 2014 3:31 pm
Location: Heathfield, sussex

Re: FM, What have I done project

Post by Macvfork » Sun Oct 09, 2016 7:41 pm

Soorry, having problems resizing photos and know how much you all like photos.
Tubs picture below - I hope.
Attachments
IMG_0488.JPG
IMG_0488.JPG (100.29 KiB) Viewed 3291 times
85-KB-13 S3 lwt. Nato green GS ex 1LI, 40 RM
03-GF-35 S3 air portable DIS 1/75 ex NIM (V), 41 Cdo RM, RE, RCT, AMB SQN
300Tdi Disco 1 com for Rtv trials.

Post Reply