Rebuild of 05 HH 50 GS SIII

Tell us about any of your Land Rover related projects here.
Post Reply
prague1996
Posts: 113
Joined: Sun Oct 06, 2013 6:36 pm

Re: Rebuild of 05 HH 50 GS SIII

Post by prague1996 » Tue Mar 04, 2014 5:00 pm

Quick update...chassis stripped, well nearly....steering relay is refusing to budge. When I flip the chassis over to clean the underside I'm hoping a liberal dose of plusgas and some gentle persuasion will tease it out.
chassis.jpg
chassis.jpg (500.08 KiB) Viewed 2220 times
Have started to strip off the bitumen and oil in preparation for painting I have been pleasantly surprised by the condition of the chassis. That said have found another hole on the chassis rail, and having seen the quality of some of the other rebuilds I also plan to redo one of the previous repairs...problem is I need to find a decent mobile welder.

Next job is to carry out a light strip down of the axles, to check the condition of the swivels, half shafts, wheel bearings and difs.

If funds allow I would like to buy a compressor (for painting and blasting) and a DIY shot blaster that can take different media so I can tackle the more delicate body panels as wells as the chassis/axles, etc....can anyone recommend a DIY shot blaster?

prague1996
Posts: 113
Joined: Sun Oct 06, 2013 6:36 pm

Re: Rebuild of 05 HH 50 GS SIII

Post by prague1996 » Mon Mar 17, 2014 4:41 pm

Managed to get the axles stripped, thankfully no nasty surprises. Although, one of the hub nuts had be done up using the blade of a screwdriver which made it difficult to remove even with a hub nut spanner. Other surprise was the amount of crap inside the leather gaiters on the front swivels. I don't have them fitted on my 109, so will probably leave them off when I rebuild the axles. Started to clean them up prior to painting but the layers of MOD underseal seem impervious to a wire brush drill bit! So resorting to hot air gun and a stanley knife blade....slow progress but I'm getting there.

Having trouble loading photo, will try again later

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Rebuild of 05 HH 50 GS SIII

Post by AR4412 » Mon Mar 17, 2014 6:56 pm

I feel your underseal pain. I've been using a hot air gun and a wallpaper scraper to remove it from my project, then using Turps and a scotchbrite pad to remove what remains. A few hours of removing the stuff does wonders for your tennis elbow.

The next area to remove it from on my project is the underside of the tub, can't wait to start that job.

Have you managed to remove the steering relay yet?

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

prague1996
Posts: 113
Joined: Sun Oct 06, 2013 6:36 pm

Re: Rebuild of 05 HH 50 GS SIII

Post by prague1996 » Tue Mar 18, 2014 5:27 pm

Hi Neil,

Top tip with the turps and scotch bright.

One of the 4x nuts that holds the steering relay on is refusing to budge. When I turn the chassis over to clean it up I'm hoping I'll have more luck removing it. Then I hope I can drift it out with a wooden block and a persuader.

Shaun

prague1996
Posts: 113
Joined: Sun Oct 06, 2013 6:36 pm

Re: Rebuild of 05 HH 50 GS SIII

Post by prague1996 » Mon May 26, 2014 9:54 am

Well its been a while since my last post..

When I turned over the chassis the rust was a lot worse than I had hoped, particularly around the axle bump stop reinforcements and the chassis legs. So the chassis was shipped back to the welders for further repairs and two new chassis legs. Once back I continued to strip off the underseal ready for painting, and boy did that take a long time! That said it had done its job as there was plenty of the original chassis paint still in evidence.

I should point out the I have never spray painted before, but I managed to get a compressor on long term loan and figured if I was going to give it a go then the chassis was a good place to start. I'm using Rustbusters epoxy mastic 121, having thinned it for spraying as recommended it still seemed a little thick but it sprayed on well and I'm really pleased with the results.
Painted chassis.jpg
Painted chassis.jpg (462.27 KiB) Viewed 2103 times
Painted front axle 1.jpg
Painted front axle 1.jpg (332.32 KiB) Viewed 2103 times
I'm going to leave the paint to harden for a week before I flip it over and do the other side, whilst I'm waiting I'll spray some cavity wax into the chassis rails. I have also made a start on the axles, but I need to order some new gaskets and seals before I start to rebuild them. It feels as though I have really turned a corner, let the rebuild begin!

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Rebuild of 05 HH 50 GS SIII

Post by AR4412 » Mon May 26, 2014 11:03 am

Hi Shaun,

Glad to hear that you've got the chassis welded up, looks good. It's good to be able to save such a large and important identifying part of the vehicle.

I had a Series III come into work on Friday for a service, pre MOT check over and a 1" hole in the chassis sorting. The hole turned out to be a foot of rotten chassis from the rear tank/tub outrigger backwards, with the tank needing to come out to check the chassis behind as it feels a bit 'soft' behind the tank. Had a look around the rest of the chassis with regards to work for the MOT and it wasn't pretty. All the outriggers have been previously replaced but it looks like they were welded on over the original rot which has now crept past them. There are holes under both front and rear bumpstops, the rot has crept past where the front dumb irons were replaced and the chassis has cracked around where a patch was welded to the underside of the number one crossmember, with the crack extending up the inside rear of the crossmember. It makes my chassis look fantastic by comparison. The vehicle is now sat in our compound waiting on a decision by the owner. If he wants it repaired it looks like I'm going to be a busy boy.

I'm glad you feel that the corner has been turned and I look forwards to seeing it all go back together again. :D

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

User avatar
Bob Fell
Cake Guru
Posts: 3044
Joined: Wed Sep 18, 2013 7:17 am
Location: Melton Mowbray

Re: Rebuild of 05 HH 50 GS SIII

Post by Bob Fell » Mon May 26, 2014 6:21 pm

Hi Shaun

Good progress, looks good too, bet your pleased!

Keep up with the pics as you progress.

Regards

Bob

PS, sounds like a new chassis is best option with that one Neil. Good buy with the tyres at Eastnor btw.
042Bobf


19HF27 Lightweight FFR ex Gurkha Field Force HQ, various Gurkha Sigs Tps and Comp Ord Depot Hong Kong 1980-1997.
42ET39 Narrow Track Sankey ex BAOR 22 & 7 Sig Regts, 16/5 Lancers, 2 RTR, 9/12 Lancers & QDG 1969-2001.

User avatar
AR4412
Maître Pâtissier
Posts: 8938
Joined: Thu Sep 22, 2011 9:31 am
Location: Bedford

Re: Rebuild of 05 HH 50 GS SIII

Post by AR4412 » Mon May 26, 2014 8:32 pm

Hi Bob,

I think you're right and it's time for a new chassis on the one at work. I don't fancy having to sort it out if he decides on repairing it that's for sure.

Regards,
For Those That Have Had To Fight for It, Life Has Truly A Flavour The Protected Will Never Know.

'First my weapon. Then my equipment. Then myself.'

Neil.

09FM98. 1973 Ex SIII FFR Now 3.5 V8 LWT Coiler.
55HG98. 1980 SIII FFR PARA RECCE. Ex 1, 2 and 3 PARA.
Td5 90 XS.

prague1996
Posts: 113
Joined: Sun Oct 06, 2013 6:36 pm

Re: Rebuild of 05 HH 50 GS SIII

Post by prague1996 » Tue Jun 03, 2014 7:28 pm

Neil/Bob thanks for your comments and encouragement.

Well the sun shone this weekend so I was able to crack on with the chassis, having applied some cavity wax I flipped it over. Thankfully I had already removed most of the underseal, but I feel everybody's pain. It's worth it in the end though. So having degressed the chassis it was on with the paint. Also managed to get some of the suspension and axle parts in paint.
painted chassis2.jpg
painted chassis2.jpg (233.5 KiB) Viewed 2068 times
Have ordered the parts (gaskets, seal's, etc..) needed to rebuild the axles, suspension and brakes.

HELP PLEASE The one part I can't source is the clip that secures the brake pipe to the rear axle casing. It's a bit like a Jubilee clip but is tightened up with a split pin. If the more learned members on the forum have the part no. or better still know where I could get one I would be very grateful. Many thanks

User avatar
Bob Fell
Cake Guru
Posts: 3044
Joined: Wed Sep 18, 2013 7:17 am
Location: Melton Mowbray

Re: Rebuild of 05 HH 50 GS SIII

Post by Bob Fell » Tue Jun 03, 2014 7:51 pm

HELP PLEASE The one part I can't source is the clip that secures the brake pipe to the rear axle casing. It's a bit like a Jubilee clip but is tightened up with a split pin. If the more learned members on the forum have the part no. or better still know where I could get one I would be very grateful. Many thanks
Hi Shaun

I will check tomorrow, I think I know what you're about .

Neil will probably beat me to it, his knowledge seems to be second to none! cannot fault him, he has helped me a lot in the past with part numbers, as has Norman but I think he's in France which is where I shall be in just over 2 weeks :D

Regards

Bob
042Bobf


19HF27 Lightweight FFR ex Gurkha Field Force HQ, various Gurkha Sigs Tps and Comp Ord Depot Hong Kong 1980-1997.
42ET39 Narrow Track Sankey ex BAOR 22 & 7 Sig Regts, 16/5 Lancers, 2 RTR, 9/12 Lancers & QDG 1969-2001.

Post Reply