Search found 8310 matches
- Fri Oct 30, 2026 9:25 pm
- Forum: General Land Rover information
- Topic: transfer case
- Replies: 4
- Views: 3143
Re: transfer case
I won't say it's impossible, but, it wouldn't be fun. It isn't a fun job with the transfer box upside down on the bench in the garage/workshop, especially if it is an all helical gear type. As well as the rear output/speedo drive housing, the front output housing has to be removed from the main casi...
- Sat Oct 24, 2026 8:50 pm
- Forum: Problems
- Topic: Both heater and wipers/washer not working
- Replies: 4
- Views: 674
Re: Both heater and wipers/washer not working
Hi Andrew, The only common item the two circuits share is the ignition switch. But, if that wasn't putting out voltage to the fusebox/wiper fuse, there would be more ignition controlled circuits inoperative than just the wiper motor. A common problem if the washer pump works, but the wiper motor doe...
- Wed Oct 07, 2026 7:57 pm
- Forum: Problems
- Topic: Tub crossmember replacement and seat belt mount/anchor
- Replies: 18
- Views: 20065
Re: Tub crossmember replacement and seat belt mount/anchor
Hi Chris, The bulkhead outriggers on the Lightweight are shorter in length between the chassis rail and the bulkhead bolt hole centre, and the bolt hole centre to the outer face than the civilian outriggers, but they can be cut down to suit. IIRC the measurements are 335mm from the chassis rail to t...
- Wed Oct 07, 2026 7:47 pm
- Forum: Problems
- Topic: Tub crossmember replacement and seat belt mount/anchor
- Replies: 18
- Views: 20065
Re: Tub crossmember replacement and seat belt mount/anchor
Hi Stuey,
I used PLIOGRIP 5761B Epoxy.
Regards,
I used PLIOGRIP 5761B Epoxy.
Regards,
- Thu Oct 01, 2026 8:07 am
- Forum: Problems
- Topic: Tub crossmember replacement and seat belt mount/anchor
- Replies: 18
- Views: 20065
Re: Tub crossmember replacement and seat belt mount/anchor
Did they forget to turn the gas on?
Regards,
- Tue Sep 29, 2026 8:29 pm
- Forum: Problems
- Topic: Tub crossmember replacement and seat belt mount/anchor
- Replies: 18
- Views: 20065
Re: Tub crossmember replacement and seat belt mount/anchor
Hi Chris, The No.5 crossmember itself is the same as that used on the SIII 88", apart from the type of tub mounting point, and is available from DDS Metal Services and Emberton Imperial from memory. It comes as a plain crossmember without any tub mountings on it. I'm not aware of anyone produci...
- Sat Sep 26, 2026 10:37 am
- Forum: General Land Rover information
- Topic: Airportable 24V electrical cut-off isolator lever.
- Replies: 6
- Views: 5842
Re: Airportable 24V electrical cut-off isolator lever.
Thats a nice straight looking truck. Thanks for sharing the pics of it.
Built under the same contract as mine. So in theory, it should be the exactly the same from the factory.
Regards,
Built under the same contract as mine. So in theory, it should be the exactly the same from the factory.
Regards,
- Wed Sep 23, 2026 8:02 pm
- Forum: General Land Rover information
- Topic: Airportable 24V electrical cut-off isolator lever.
- Replies: 6
- Views: 5842
Re: Airportable 24V electrical cut-off isolator lever.
Hi, and welcome to the forum. Feel free to add some pics of your truck if you wish to. We like piccies we do. And cake. The battery cut off switch is probably a P.O. addition as they weren't fitted in service. You don't say what type of switch is fitted, of an all metal or plastic construction, or w...
- Wed Sep 23, 2026 7:49 pm
- Forum: General Land Rover information
- Topic: transfer case
- Replies: 4
- Views: 3143
Re: transfer case
It is possible, but it's a heavy old lump to manoeuvrer around from underneath with the vehicle sat on it's wheels. Not so bad to do if the floor and seat box are out of the vehicle and the transfer box supported from above for lifting and lowering.
Regards,
Regards,
- Wed Sep 23, 2026 7:43 pm
- Forum: General Land Rover information
- Topic: Raising the rear tub
- Replies: 6
- Views: 12183
Re: Raising the rear tub
Given all the nuts and bolts for the lashing points, rivets, and spot welds that need to be removed to get the floor out, it would be easier to remove the complete tub.
Regards,
Regards,